If you live in Wilmslow and part of your house is clad in timber, you've probably looked at it and thought it was fine. The boards are painted or stained, they look tidy from the road, and nothing seems wrong. Then one day a board feels soft under your thumb, the finish is flaking in one patch, or there's a damp mark on the wall inside that sits right behind the cladding.
This guide explains how water gets behind timber cladding, why the space behind the boards matters so much, what trapped moisture does to the boards and the wall behind them, and what you can safely check from the ground. We're damp and timber surveyors, not cladding installers, so we'll stick to what we see and who the right person is for each job.
🏡 Why Is Timber Cladding Used On So Many Houses?
Timber cladding is a good way to finish a wall. It looks warm, it's lighter than brick, and it's popular on gables, extensions, dormers and sometimes a whole front or rear elevation. Plenty of newer homes have it, and plenty of older ones were given a clad extension or a clad gable later on.
The boards themselves are only the outer skin. Behind them there should be a layered build-up, and each layer has a job:
- The boards. They shed most of the rain, but they aren't watertight on their own. Water gets into the joints, the end grain and around openings.
- Battens. These are thin timber strips fixed to the wall that hold the boards off the surface and leave a gap behind them.
- A breathable membrane. On many walls there's a layer behind the battens that stops any water that gets past the boards from reaching the wall, while letting the wall breathe.
- The wall itself. This could be masonry, a timber frame covered in sheathing board, or a mix of both.
Timber-effect cladding in other materials works in a similar way, with boards held off the wall on battens. The same questions about the gap and the base apply to it.
When all of that works, the boards get wet in the rain and dry out again afterwards. The trouble starts when the boards stay wet, or when water gets behind them and has nowhere to go.
💧 How Does Water Get Behind Timber Cladding?
Rain doesn't have to pour through a hole to cause a problem. A little water getting in at the same spot every time it rains is enough over a few winters. These are the places we look first.
🪵 Joints and end grain
Every cut end of a board is end grain, and end grain soaks up water far faster than the face of the board. Where boards meet at a corner, or at the top and bottom of a run, the cut ends sit open to the weather. If the finish was never put on those ends, or it has worn off, water wicks in and travels along the board.
Joints between boards are the same. Over time timber swells in wet weather and shrinks in dry weather, and the finish cracks along the joint. Water then runs in behind the face of the board.
🪟 Around windows and doors
Openings are where cladding is cut, trimmed and sealed, and sealing is where it often goes wrong. Gaps open up between the boards and the window frame. A sill that has no drip, or a flashing that has lifted, can send water straight down behind the boards beneath the window. A damp patch on the inside wall under a window frame is often traced to this.
🌱 The base of the boards
The bottom edge of the cladding takes more punishment than any other part. Rain splashes up from the ground, from paving, from a flower bed or from a path built up against the wall. If the lowest board sits very close to the ground, or touches soil, it stays wet. Timber that stays wet for months is exactly what wet rot likes.
Soil banked against the wall also bridges the gap that should be left between the cladding and the ground, which is one of the quickest ways to trap moisture at the bottom of the wall.
🔩 Fixings and cracks in the finish
Nail and screw heads that aren't sealed can let water follow the fixing into the board. Cracks in paint or stain do the same on the face. Once the finish has failed in one spot, that spot soaks up water in every shower and dries more slowly each time.
🌧️ Gutters and roof edges
A gutter that overflows or a downpipe that leaks can throw water down one section of cladding again and again. If the rot is in one strip below a gutter joint or a corner of the roof, that's a strong clue.
🌬️ What Is The Gap Behind The Boards For?
The gap behind the boards is the most important part of the build-up, and the part most often overlooked.
Cladding is designed as a rainscreen. That's a simple idea: the boards take the bulk of the rain, and the gap behind them lets air move, so any water that gets past the boards can drain away or dry out. Air should be able to get in at the bottom, move up behind the boards and leave at the top.
That only works if the gap stays open. Here's how it gets closed off:
- Boards fixed straight to the wall with no battens, so there's no gap at all.
- Battens fitted sideways, so they act like shelves and stop air and water moving up and down.
- A blocked bottom edge, where a path, soil or a raised bed touches the boards.
- Insulation or filler pushed into the gap during an extension or a repair.
- Closed-off top and bottom edges, where trims, mesh or sealant have been fitted without leaving the gap open.
When the gap is closed, water that gets behind the boards stays there. The wall behind can't dry the way it should, and the back of the boards stays damp for far longer than the front. From outside you'd never know, because the face of the cladding can look sound while the back is wet.
🪵 What Happens When Moisture Gets Trapped Behind Cladding?
Timber that stays damp doesn't stay sound. It's worth knowing the order things tend to happen in, because early signs are easy to miss.
🎨 The finish fails first
Paint or stain flakes, blisters or peels in patches. Water gets into the bare timber and the board starts to take on more water in each wet spell.
🍂 The boards soften
A board that was firm becomes soft, spongy or fibrous. You can often press a thumbnail into it. It may crack along the grain, or break up at the bottom end first. This is typical of wet rot, which affects timber that stays wet.
🔩 The battens and fixings go next
Battens sit in the damp gap and take up water from behind. They're often thinner and less well finished than the boards, and they can rot while the boards still look reasonable. When a batten softens, the boards fixed to it can loosen, bow or move.
🧱 The wall behind gets wet
Once the gap is full of moisture, the membrane and the sheathing board or the masonry behind it stay wet as well. In a timber-framed wall, that can reach the sheathing, the frame and the insulation. In a masonry wall, it can show up inside as a damp patch, flaking paint or a musty smell on the back of the wall behind the cladding.
🍄 Fungal growth
On the surface, you may see green algae, black spotting or white fungal growth. Algae alone just means the board is damp on the outside. A fungus growing in or behind the boards means the timber has been wet for a while.
🔬 Wet rot or dry rot?
Most timber decay in exposed places like cladding is wet rot. It needs the timber to stay quite wet, and it usually stays in the area that's wet. Dry rot is different. It can spread through masonry and into timber that isn't directly wet, and it needs a proper survey. Telling the two apart by eye is hard. The signs, the pattern and where the moisture is coming from all matter, which is why a survey looks at the whole picture, not just one board.
For more on both, see our pages on wet rot treatment and dry rot treatment.
🏘️ Why Might Wilmslow Homes Run Into This?
Wilmslow is in Cheshire, where autumns and winters are often wet, and a house with timber cladding gets wetter and stays wetter in the months when the wall has least chance to dry. A clad gable or a clad rear extension is a common way to finish an extension, and homes of all ages have them.
We can't say what's behind any particular wall without looking at it. What we can say is that the places where cladding fails are very consistent from house to house: the joints at corners, the area under windows, the bottom board, and any section below a gutter or downpipe. If your home has cladding, those are the spots to look at first.
If you'd like to know more about how we work in the area, our page for damp specialists in Wilmslow covers it.
👀 What Can You Check From The Ground?
You don't need a ladder or any tools for a first look. Walk round the house on a dry day and check the following.
- The bottom board. Is there a clear gap between the lowest board and the ground, a path or a flower bed? If soil, bark or paving touches the board, that's a likely cause.
- Soft boards. Press gently with a thumb at the bottom of the boards, at the corners and below the windows. A board that gives, feels spongy or marks easily is one to write down.
- Flaking or blistered finish. Look for patches where the paint or stain has lifted, especially on boards that get the most weather.
- Swelling, bowing or gaps. Boards that have pulled away from their fixings, or that have swollen, may have a wet batten behind them.
- Green or black growth. A patch of algae in one spot often follows a splash zone or a leaking gutter.
- Gutters and downpipes. Look for stains running down the boards below a joint, an overflow or a corner. Checking the gutter in heavy rain, from a safe place, shows where water is landing.
- Window and door junctions. Look for gaps, cracked sealant or stained boards right under a window sill.
- The inside wall. If there's a damp mark, flaking paint or a musty smell on the inside of the wall behind the cladding, note where it is compared with the outside.
Take photographs as you go, with something in the shot to show scale. They help you see whether things are changing, and they help a surveyor.
If a board looks fine but you notice a damp patch inside, don't assume the cladding is the cause. The patch could come from the cladding, a gutter, a leaking pipe or condensation. A surveyor will take readings to separate them.
🔎 How Can You Tell A Cladding Problem From Other Damp?
Damp on a wall behind cladding isn't always the cladding's fault, and rot in a board isn't always a sign that the wall is wet. This table is a rough guide to the patterns we look for.
| What you see | What it often points to |
|---|---|
| Soft boards at the bottom, soil or paving touching them | Splashback and ground contact at the base |
| Rot or staining in one strip below a gutter joint | A leaking or overflowing gutter |
| Staining and soft timber directly under a window | Water getting in at the window junction |
| Flaking finish on the sunniest or most exposed side | A worn finish, with water getting into bare timber |
| Damp patch inside that follows the rain, with sound boards outside | Water getting past the cladding, or another route in |
| Damp patch inside that stays the same whatever the weather | A leak or ground moisture |
| Mould on the inside of the wall in winter, worse in cold weather | Condensation, with or without a cladding problem |
Two things help a lot. The first is timing: does the damp get worse after rain, or does it stay put? The second is location: damp that lines up with a window, a gutter or the base of the wall points to a particular route for the water.
A damp meter can't settle this on its own, because a wet surface reads wet whatever has made it wet. That's why a surveyor looks at the outside of the house first, including the gutters and the ground levels, then checks inside.
🧰 What Can A Homeowner Safely Do?
A few simple jobs can slow things down while you find out what's going on.
- Clear soil, leaves and bark away from the bottom of the boards. Leave a clear gap between the cladding and the ground. If a path or patio has been built up against the boards, that needs a proper look rather than a quick fix.
- Keep plants off the cladding. Climbers hold moisture against the boards and stop them drying.
- Clear gutters and check downpipes so they don't overflow onto the wall.
- Keep the finish in good order. Touching up small areas of flaking finish, including the cut ends of boards, helps keep water out. Use a product suitable for exterior timber and follow the maker's instructions.
- Don't seal up the gap. Don't fill the space behind or below the boards with sealant, foam or filler. That can trap moisture in.
- Avoid painting over soft boards. A fresh coat on top of damp or soft timber hides the problem and traps moisture beneath it.
We wouldn't suggest stripping cladding off to look behind it. Taking boards off can damage them and the membrane behind, and it's often not needed for a first answer. If boards do need to come off, that's best done by someone who can put them back properly.
🪚 Who Fixes What?
It helps to know which job belongs to whom.
A carpenter or cladding installer repairs or replaces boards and battens, fits trims and flashings, and puts the finish on. If the boards are the only problem, that's usually who you need.
A damp and timber surveyor works out where the water is coming from and what it has affected. That means looking at whether it's wet rot or something more serious, whether the wall or frame behind the cladding is wet, and whether the cause is the cladding itself, a gutter, the ground levels, a leak or condensation.
The order matters. If a carpenter replaces rotten boards without anyone finding out why they rotted, the new boards can go the same way. Finding the cause first means the repair is more likely to last.
🧪 Why Does A Timber Qualification Matter For This?
Timber problems look simple, but the cause isn't always the one you'd guess. Our surveying team includes professionals holding the Certified Surveyor of Timber & Dampness in Buildings (CSTDB) qualification, which is built around diagnosing timber decay and the damp that causes it. Our staff also have over 40 years' combined experience between them.
On a cladding visit, a surveyor will usually:
- look at the outside of the house first, including gutters, downpipes, window junctions and ground levels;
- check the boards, battens and finish for soft or stained timber;
- take moisture readings, outside and inside, across the wall behind the cladding;
- look at whether the gap behind the boards is open or blocked;
- tell you plainly what's wet, what's rotten and what's still sound.
You can read about the people who carry out the visits on our page about our qualified surveyors.
🔗 Other Timber Problems On The Outside Of A House
Cladding isn't the only exterior timber that rots from moisture. If you've found a problem somewhere else, these posts may help:
- Our post on why the bottom of a timber door frame rots covers another place where end grain and splashback cause trouble.
- Our post on why a timber fascia or soffit board rots is about the roof edge, where blocked gutters often start the problem.
- Our post on whether a rotten window sill can be repaired instead of replaced is useful if the damage is right under a window.
If you suspect rain is getting through the wall itself, our page on penetrating damp explains how that works, and our damp and mould page covers the wider picture.
❓ Questions We Hear About Timber Cladding And Damp
Can timber cladding cause damp inside the house?
It can contribute. If water gets behind the boards and can't drain or dry out, the wall behind stays wet, and that can show up as a damp patch inside. The cladding isn't always the cause, though. A gutter, a leak or condensation can produce a similar mark, so it's worth having the cause confirmed.
How do I know if the boards are rotten?
Press a thumb gently into the bottom of a board, at a corner or under a window. Sound timber is firm. Rotten timber feels soft, spongy or fibrous, and may crumble or crack along the grain. A flaking finish alone doesn't mean rot, but it lets water in.
Is the green growth on my cladding a problem?
Green algae mostly tells you the surface stays damp, often from shade, splashback or a leaking gutter. It isn't the same as rot, but it's a sign the board isn't drying as it should. Look at what is making that spot wet.
Should I paint or stain the cladding to protect it?
A sound finish helps keep water out, including on the cut ends of the boards. But painting over soft or damp timber traps moisture and hides the problem. Check the boards first, deal with any cause of wetness, and let the timber dry before refinishing.
Does the gap behind the cladding really matter?
Yes. It's what lets the back of the boards and the wall behind dry out. If it's blocked, by a path, soil, filler or boards fixed straight to the wall, water that gets behind the cladding stays there.
When is it worth getting a survey?
If boards are soft, if rot keeps coming back after repairs, if there's a damp patch inside behind the cladding, or if you're not sure what's causing it, a survey is worth having. A surveyor can tell you whether the cause is the cladding, a gutter, the ground levels, a leak or condensation, and what has been affected.
📍 Looking For A Timber And Damp Specialist In Wilmslow?
If your Wilmslow home has cladding that's soft, stained or flaking, or a damp patch on a wall behind it, we can help you find out why. We cover Wilmslow and the wider Cheshire area, and you can see more on our page for damp specialists in Wilmslow.
We're a family and friends run business, and we start by looking at the whole picture, not only the board or the patch you can see. Our surveyors will tell you what's causing it before suggesting any work.
Book your free survey by calling 01782 901101 or through our contact page, and we'll arrange a visit.











